Bbe 482I Sonic Maximizer Signal Sound Processor+Furman M-8X2 Power Conditioner
Product Description
- (1) Bbe 482I Sonic Maximizer Signal Sound Processor
- (1) Furman M-8x2 Merit 9 Outlet Rack Mount Power Conditioner
With true dual-mono operation, the 482 has two independent BBE SONIC MAXIMIZER™ signal processors in one chassis.
Video of 482I:
482I Applications:
- Pro and semi-pro sound reinforcement
- Multitrack studios
- Mobile DJ systems
- Cassette copies
- Nightclub sound systems
- Instrument racks for guitar, bass and keyboards
- 2 channels of process for stereo or separate mono mixes
- 5 segment LED output meters
- +18dBu headroom
- RCA and1/4" inputs and outputs
- Hardwire bypass
- Bypass switch for comparison of processed to unprocessed signal
- Frequency Response,
- Process Mode: Program controlled
- Bypass Mode: 10Hz to 50kHz, +/- 0.5dBu, 10dBu input
- Signal to Noise Ratio: 112dB Process IN
- THD, Process mode: less than 0.025% at 20-20kHz
- Bypass mode: less than 0.002% at 20-20kHz
- Maximum Output: +18dBu (may vary due to control settings)
- Input Impedance: 47K Ohms, unbalanced 1/4" phone jack or RCA jack.
- Output Impedance: 1K Ohms, unbalanced 1/4" phone jack or RCA jack.
- Sensitivity: -45dBu for maximum process
- Maximum Process: +12dBu boost at 5kHz, -10dBu input
- Lo Contour: +12dBu adjustment at 50Hz, -10dBu input
Description Of M-8X2 + 16 SCREWS:
We are giving away 16 rack screws so you can install this and all your other rack equipment without running around and looking for screws. These are top of the line rack screws, and they are standard sized. You do not need 16 screws to install this item, however we want you to be able to install your other rack equipment as well as the Furman conditioner!
A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-8x2 in to the top slot of your rack, and the eight switched outlets in the rear panel will power up and protect all your equipment up to a 15-amp load. The M-8x2 is designed for applications where lights are not required.
Features:
-
Noise Filtration
AC noise filtering to reduce radio frequency and electromagnetic interference (RFI/EMI) -
Surge Protection
Spike & surge protection ensures equipment stays safe and your power stays clean -
9 Total Outlets
8 rear panel outlets and 1 front panel outlet -
15 Amp Rating
15 amp rating, with circuit breaker -
"Protection OK" Indicator
Front panel indicator LED lets you know that your equipment is being protected -
Wall Wart Spacing Indicator
Rear outlets have been spaced to accommodate even the bulkiest of wall warts and adapters
Applications:
Instrument Rigs
You've got a rack for your effects, preamps, tuner...You're going to plug that into the wall? One big spike and your rig is up in smoke. Furman's standard level surge/spike protection defends your gear from the spikes and surges that are so common at gigs and practice spots. With Furman's standard level RFI/EMI filtration, you'll get a quieter tone without pops, crackles, and the local radio station coming out of your amp.
Recording
Can't track down where that noise is coming from? Your mix sounding flat? With Furman's standard level RFI/EMI filtration you'll lower the noise floor caused by the dirty AC power coming into your console or DAW. Furman's standard level surge and spike protection keeps your sensitive digital equipment from acting funny or burning up due to everyday spikes and surges. With a 15A capacity and nine total outlets, it's enough to power your whole home studio.
DJ Equipment
Bars, clubs and other event venues have some of the worst power out there - from air compressors turning on and off to light shows pulling current loads up and down, the AC power can be a strain on the circuits in your rig. Furman's standard level protection and filtration keeps the bad stuff out.
Pro Audio
When you're out there gigging, you never know what kind of power you're going to get. The wear and tear on mobile rigs eventually takes it toll - that's why it's smart to plug into Furman's standard level protection and RFI/EMI filtration. It keeps your equipment safe and sounding clean. Whether you're setting up a show at the local club or powering up the church band for their next service, make sure you give them power they can trust.
Surge protection and why it is important:
This is the most important component you will have in your rack. The reason is because if you do not have a good surge protector that is reliable, all your equipment can easily blow out and stop working. A simple surge in voltage coming from the AC outlet can cause this to happen. Get the Furman M-8X2 and keep your expensive equipment protected!
Specifications:
| Maximum Output Current: | 15 amps |
| Line Cord: | 6 ft., captive, 14 AWG, with 3-conductor Edison plug |
| Operating Voltage: | 120VAC 60Hz |
| Spike Protection Mode: | Line to neutral |
| Energy Dissipation: | 170 joules |
| Peak Impulse Current: | 12,000 amps |
| Maximum Continuous Opterating Voltage: | 130 VAC RMS |
| Let Through Voltage (@ 125 amps, 8/20uS waveform) | 400 volts |
| Noise Attenuation: | Transverse mode: Greater than 23dB, 200Khz to 10 Mhz |
| Dimensions: | 1.75” H x 19” W x 3.75” D |
| Weight: | 4.9 lbs. |
| Safety Agency Listing: | cTUVus |
| Warranty: | Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship. |
For over 30 years Furman has been the, hands-down leader, and most trusted brand name for AC Conditioning, AC Regulation, balanced Isolation transformers, Power Sequencing, and Power Distribution for audio, video, and broadcast professionals. Furman is used by the best studios, DJ's, clubs, professional musicians, contractors, and audio engineers across the world. They choose Furman because of reliability, quality, engineering expertise, and because Furman knows the specific needs of professionals who can't afford to have downtime or equipment failure.
We are giving away 16 rack screws so you can install this and all your other rack equipment without running around and looking for screws. These are top of the line rack screws, and they are standard sized. You do not need 16 screws to install this item, however we want you to be able to install your other rack equipment as well as the Furman conditioner!
#1 Authorized 
Internet Retailer!
We have the biggest selection of Furman products! Click here to find the Furman product you are looking for. Do not see the item you are looking for ? E-mail us the model(s) you are looking for and we will give you a price quote.
Shipping & Returns
Row content
