(2) JBL Control 25-1 5.25" 30w 70v Wall-Mount Commercial Restaurant/Bar Speakers
(2) JBL Control 25-1 5.25" 30w 70v Wall-Mount Commercial Restaurant/Bar Speakers
JBL
(2) JBL Control 25-1 5.25" 30w 70v Wall-Mount Commercial Restaurant/Bar Speakers
(2) JBL Control 25-1 5.25" 30w 70v Wall-Mount Commercial Restaurant/Bar Speakers
5.25" Two-Way Indoor/Outdoor Speaker Pair, 200W Program, 30W 70V Taps, InvisiBall Mounting Hardware Included
Free Shipping
Features
- 5.25 in woven-fiberglass woofer and 0.75 in PEI diaphragm tweeter
- 200 W program handling at 8 ohms with 90 dB sensitivity
- 70V taps at 30 W, 15 W, 7.5 W and 3.7 W for distributed lines
- IP-44 weatherized enclosure tested past Mil Spec 810 for salt and UV
- InvisiBall hardware mounts through a hidden point behind the badge
Couldn't load pickup availability
What's Included in the box
- Two Control 25-1 speakers (white)
- Two InvisiBall wall-mounting systems
SKU: SKU: CONTROL 25-1-WH
View full details









Product Description
The 5.25 in woven-fiberglass woofer uses a butyl rubber surround with WeatherEdge frame protection, a high-temperature Kapton voice coil former, and a linear suspension spider. Cone geometry is shaped for consistent response off-axis, which matters in rooms where people are rarely standing on the speaker's centerline. The 0.75 in PEI diaphragm tweeter with ferro-magnetic fluid keeps the high end even rather than sharp.
Coverage is 100 by 100 degrees, and frequency response runs 60 Hz to 20 kHz at minus 10 dB, 85 Hz to 17 kHz within plus or minus 3 dB.
Wiring works either way. Take the 8 ohm thru setting for a local amplifier, or select the built-in multi-tap transformer at 30 W, 15 W, 7.5 W, or 3.7 W on 70V lines (100V: 30 W, 15 W, 7.5 W) with under 0.94 dB insertion loss at any tap.
JBL's InvisiBall mounting hardware installs through a hidden access point behind the logo badge, so nothing visible holds the speaker to the wall and casual removal is not an option. The high-impact polystyrene enclosure and zinc-plated grille carry IP-44 protection, exceed Mil Spec 810 for humidity, salt spray, temperature, and UV, and pass ASTM G85 acid-air and salt-spray testing.
The white finish takes paint, so the speakers can match any wall. Each unit measures 9.6 x 7.4 x 5.7 in and weighs 7.5 lb.
Features
Loud From A Small Amplifier
Sensitivity of 90 dB and 200 W program handling mean a modest amplifier channel reaches high output across a patio, gym floor, or cafe.
Sounds Right Off-Axis
Optimized cone geometry and a fluid-cooled PEI tweeter keep response even for listeners standing well off the speaker's centerline, which is most of the room.
Invisible Mounting
InvisiBall hardware installs through a hidden access point behind the logo badge, leaving no visible bracket and deterring walk-off in public areas.
Built For Weather
WeatherEdge frame protection, Kapton voice coil formers, and an IP-44 enclosure handle rain, heat, and salt air in covered outdoor installations.
Paint It To Match
The high-impact polystyrene cabinet accepts a range of finishes and pigments, so the speakers can blend into any wall color on site.
Technical Specifications
- Product Type 5.25 in Two-Way Indoor/Outdoor Surface-Mount Speaker (Pair)
- Frequency Response (+/-10 dB) 60 Hz - 20 kHz
- Frequency Response (+/-3 dB) 85 Hz - 17 kHz
- Power Rating 200 W continuous program, 100 W (400 W peak) continuous pink noise
- Sensitivity 90 dB, 1W/1m
- Coverage Angle 100 degrees x 100 degrees
- Nominal Impedance 8 ohms (thru setting)
- Maximum Input Voltage 25.3 V RMS, 50.6 V peak
- Transformer Taps 70V: 30 W, 15 W, 7.5 W, 3.7 W / 100V: 30 W, 15 W, 7.5 W
- Drivers 5.25 in woven-fiberglass woofer, 0.75 in PEI diaphragm tweeter
- Crossover Type 2nd order low-pass, 2nd order high-pass
- Enclosure High-impact polystyrene
- Grille Zinc-plated steel with TGIC polyester powder coating
- Environmental IP-44 per IEC529, exceeds Mil Spec 810, ASTM G85 tested
- Mounting InvisiBall hidden wall-mount hardware included
- Color White
- Weight 7.5 lb each
- Dimensions 9.6 x 7.4 x 5.7 in (H x W x D)